A
-
A390 alloy
Effect of Pouring Temperature and Partial Remelting on Microstructure and Wear Properties of A390 Alloy in Slope Cooling Casting [Volume 1, Issue 1, 2017-2018, Pages 37-46]
-
A520 Al-alloy
Effect of Severe Plastic Deformation on Mechanical Properties and Microstructure of A520 Al-Alloy Produced by Semisolid and Ordinary Casting [Volume 1, Issue 1, 2017-2018, Pages 9-21]
-
Al-2Ni
An Investigation on the Effect of Mn on the Castability of Hypoeutectic Al-2Ni-xMn Alloys [Volume 1, Issue 2, 2017-2018, Pages 69-78]
-
Al-5Cu-1Ag alloy
Semi-Solid Rheocasting of Al-5Cu-1Ag High Strength Alloy [Volume 1, Issue 3, 2017-2018, Pages 193-200]
-
Al-Fe alloy
Investigation on the Effect of Solidification Parameters on Microstructural Characteristics and Hardness of Al-Fe Alloy Produced by Directional Solidification in Bridgeman Furnace [Volume 1, Issue 1, 2017-2018, Pages 1-8]
-
Al-Si alloys
The Effect of Silicon Content on the Graded Microstructure of Centrifugally Cast Al-Si Alloys [Volume 1, Issue 2, 2017-2018, Pages 89-97]
-
Alumina
Evaluation of the Microstructure and Wear Properties of A356/Al2O3 Nanocomposite Produced by Stir Casting Method [Volume 1, Issue 1, 2017-2018, Pages 59-68]
-
Aluminium
Evaluation of the Microstructure and Wear Properties of A356/Al2O3 Nanocomposite Produced by Stir Casting Method [Volume 1, Issue 1, 2017-2018, Pages 59-68]
-
Aluminium
Using Thermal Analysis and Interrupted Quenching Technique to Examine Interactive Effect of Bi-Sr on Porosity Formation Characteristics in Al-7Si-0.4Mg Alloy [Volume 1, Issue 3, 2017-2018, Pages 181-191]
-
Austempering
Effect of Austempering Time and Temperature on the Microstructure and Hardness of Bainitic Silicon Steel [Volume 1, Issue 2, 2017-2018, Pages 79-87]
B
-
Bainitic-ferrite
Effect of Austempering Time and Temperature on the Microstructure and Hardness of Bainitic Silicon Steel [Volume 1, Issue 2, 2017-2018, Pages 79-87]
-
Bismuth
Using Thermal Analysis and Interrupted Quenching Technique to Examine Interactive Effect of Bi-Sr on Porosity Formation Characteristics in Al-7Si-0.4Mg Alloy [Volume 1, Issue 3, 2017-2018, Pages 181-191]
-
Bridgeman furnace
Investigation on the Effect of Solidification Parameters on Microstructural Characteristics and Hardness of Al-Fe Alloy Produced by Directional Solidification in Bridgeman Furnace [Volume 1, Issue 1, 2017-2018, Pages 1-8]
-
Bridgman Technique
The Effect of Precipitation Hardening on Microstructural Characteristics of Directionally Solidified Nickel-Based Superalloy GTD-111 [Volume 1, Issue 2, 2017-2018, Pages 109-120]
C
-
Castability
An Investigation on the Effect of Mn on the Castability of Hypoeutectic Al-2Ni-xMn Alloys [Volume 1, Issue 2, 2017-2018, Pages 69-78]
-
Casting
Evaluation of the Microstructure and Wear Properties of A356/Al2O3 Nanocomposite Produced by Stir Casting Method [Volume 1, Issue 1, 2017-2018, Pages 59-68]
-
Cellular growth
Investigation on the Effect of Solidification Parameters on Microstructural Characteristics and Hardness of Al-Fe Alloy Produced by Directional Solidification in Bridgeman Furnace [Volume 1, Issue 1, 2017-2018, Pages 1-8]
-
Coefficient of thermal expansion
Evaluation of Microstructure, Physical and Mechanical Properties of Functionally Graded Al-Cu Fabricated by Horizontal Centrifugal Casting [Volume 1, Issue 1, 2017-2018, Pages 47-58]
-
Cooling Slope
Effect of Pouring Temperature and Partial Remelting on Microstructure and Wear Properties of A390 Alloy in Slope Cooling Casting [Volume 1, Issue 1, 2017-2018, Pages 37-46]
D
-
Directional Solidification
Investigation on the Effect of Solidification Parameters on Microstructural Characteristics and Hardness of Al-Fe Alloy Produced by Directional Solidification in Bridgeman Furnace [Volume 1, Issue 1, 2017-2018, Pages 1-8]
-
Directional Solidification
The Effect of Precipitation Hardening on Microstructural Characteristics of Directionally Solidified Nickel-Based Superalloy GTD-111 [Volume 1, Issue 2, 2017-2018, Pages 109-120]
E
-
Eddy current
Microstructure and Hardness Evaluation of Heat Treated Cast Steel by Eddy Current Nondestructive Method [Volume 1, Issue 3, 2017-2018, Pages 149-160]
-
Elastic modulus
Evaluation of Microstructure, Physical and Mechanical Properties of Functionally Graded Al-Cu Fabricated by Horizontal Centrifugal Casting [Volume 1, Issue 1, 2017-2018, Pages 47-58]
F
-
Fluidity
An Investigation on the Effect of Mn on the Castability of Hypoeutectic Al-2Ni-xMn Alloys [Volume 1, Issue 2, 2017-2018, Pages 69-78]
-
Functionally graded
The Effect of Silicon Content on the Graded Microstructure of Centrifugally Cast Al-Si Alloys [Volume 1, Issue 2, 2017-2018, Pages 89-97]
G
-
Gamma Prime
The Effect of Precipitation Hardening on Microstructural Characteristics of Directionally Solidified Nickel-Based Superalloy GTD-111 [Volume 1, Issue 2, 2017-2018, Pages 109-120]
-
Gamma prime precipitates
Effect of Solution Treatment on the Microstructure of γ' Precipitates in the IN738LC Superalloy Before and After Aging [Volume 1, Issue 2, 2017-2018, Pages 99-108]
-
Grades of sand
Experimental Investigation of Effective Parameters on Gas Exhaust from the Mold in Lost Foam Casting Method [Volume 1, Issue 3, 2017-2018, Pages 161-170]
-
Graphite distribution
The Effect of Pouring Temperature on Graphitization of Cast Bars Produced by in-Mold Lost Foam Process [Volume 1, Issue 1, 2017-2018, Pages 23-35]
H
-
Hardness
Microstructure and Hardness Evaluation of Heat Treated Cast Steel by Eddy Current Nondestructive Method [Volume 1, Issue 3, 2017-2018, Pages 149-160]
-
Hardness
Effect of Shot-Peening on the Wear Behavior of Two Types of High Manganese Austenitic Steel [Volume 1, Issue 2, 2017-2018, Pages 121-132]
-
High manganese austenitic steel
Effect of Shot-Peening on the Wear Behavior of Two Types of High Manganese Austenitic Steel [Volume 1, Issue 2, 2017-2018, Pages 121-132]
-
Hot tear
Semi-Solid Rheocasting of Al-5Cu-1Ag High Strength Alloy [Volume 1, Issue 3, 2017-2018, Pages 193-200]
-
Hot tearing
An Investigation on the Effect of Mn on the Castability of Hypoeutectic Al-2Ni-xMn Alloys [Volume 1, Issue 2, 2017-2018, Pages 69-78]
I
-
IN738LC superalloy
Effect of Solution Treatment on the Microstructure of γ' Precipitates in the IN738LC Superalloy Before and After Aging [Volume 1, Issue 2, 2017-2018, Pages 99-108]
-
In-mold lost foam process
The Effect of Pouring Temperature on Graphitization of Cast Bars Produced by in-Mold Lost Foam Process [Volume 1, Issue 1, 2017-2018, Pages 23-35]
-
Intermetallic compound
Investigation on the Effect of Solidification Parameters on Microstructural Characteristics and Hardness of Al-Fe Alloy Produced by Directional Solidification in Bridgeman Furnace [Volume 1, Issue 1, 2017-2018, Pages 1-8]
L
-
Lead-free
Production and Characterization of SAC-xAl Lead Free Nanocomposite Solder via Melt-Spinning Technique [Volume 1, Issue 3, 2017-2018, Pages 171-180]
-
Lost foam casting
Experimental Investigation of Effective Parameters on Gas Exhaust from the Mold in Lost Foam Casting Method [Volume 1, Issue 3, 2017-2018, Pages 161-170]
M
-
Mechanical properties
Effect of Severe Plastic Deformation on Mechanical Properties and Microstructure of A520 Al-Alloy Produced by Semisolid and Ordinary Casting [Volume 1, Issue 1, 2017-2018, Pages 9-21]
-
Mechanical properties
Semi-Solid Rheocasting of Al-5Cu-1Ag High Strength Alloy [Volume 1, Issue 3, 2017-2018, Pages 193-200]
-
Melt spinning
Production and Characterization of SAC-xAl Lead Free Nanocomposite Solder via Melt-Spinning Technique [Volume 1, Issue 3, 2017-2018, Pages 171-180]
-
Microstructure
Effect of Severe Plastic Deformation on Mechanical Properties and Microstructure of A520 Al-Alloy Produced by Semisolid and Ordinary Casting [Volume 1, Issue 1, 2017-2018, Pages 9-21]
-
Microstructure
Microstructure and Hardness Evaluation of Heat Treated Cast Steel by Eddy Current Nondestructive Method [Volume 1, Issue 3, 2017-2018, Pages 149-160]
-
Microstructure
Semi-Solid Rheocasting of Al-5Cu-1Ag High Strength Alloy [Volume 1, Issue 3, 2017-2018, Pages 193-200]
N
-
Nanocomposite
Evaluation of the Microstructure and Wear Properties of A356/Al2O3 Nanocomposite Produced by Stir Casting Method [Volume 1, Issue 1, 2017-2018, Pages 59-68]
-
Nanocomposite
Production and Characterization of SAC-xAl Lead Free Nanocomposite Solder via Melt-Spinning Technique [Volume 1, Issue 3, 2017-2018, Pages 171-180]
-
Nickel-Based Superalloy
The Effect of Precipitation Hardening on Microstructural Characteristics of Directionally Solidified Nickel-Based Superalloy GTD-111 [Volume 1, Issue 2, 2017-2018, Pages 109-120]
-
Nodular graphite cast iron
The Effect of Pouring Temperature on Graphitization of Cast Bars Produced by in-Mold Lost Foam Process [Volume 1, Issue 1, 2017-2018, Pages 23-35]
-
Nondestructive evaluation
Microstructure and Hardness Evaluation of Heat Treated Cast Steel by Eddy Current Nondestructive Method [Volume 1, Issue 3, 2017-2018, Pages 149-160]
P
-
Partial Solution
The Effect of Precipitation Hardening on Microstructural Characteristics of Directionally Solidified Nickel-Based Superalloy GTD-111 [Volume 1, Issue 2, 2017-2018, Pages 109-120]
-
Polystyrene foam
The Effect of Pouring Temperature on Graphitization of Cast Bars Produced by in-Mold Lost Foam Process [Volume 1, Issue 1, 2017-2018, Pages 23-35]
-
Pouring Temperature
The Effect of Pouring Temperature on Graphitization of Cast Bars Produced by in-Mold Lost Foam Process [Volume 1, Issue 1, 2017-2018, Pages 23-35]
-
Pouring Temperature
Effect of Pouring Temperature and Partial Remelting on Microstructure and Wear Properties of A390 Alloy in Slope Cooling Casting [Volume 1, Issue 1, 2017-2018, Pages 37-46]
Q
-
Quality Control
Microstructure and Hardness Evaluation of Heat Treated Cast Steel by Eddy Current Nondestructive Method [Volume 1, Issue 3, 2017-2018, Pages 149-160]
R
-
Rapid solidification
Production and Characterization of SAC-xAl Lead Free Nanocomposite Solder via Melt-Spinning Technique [Volume 1, Issue 3, 2017-2018, Pages 171-180]
-
Reheating Temperature
Effect of Pouring Temperature and Partial Remelting on Microstructure and Wear Properties of A390 Alloy in Slope Cooling Casting [Volume 1, Issue 1, 2017-2018, Pages 37-46]
-
Rheocasting
Semi-Solid Rheocasting of Al-5Cu-1Ag High Strength Alloy [Volume 1, Issue 3, 2017-2018, Pages 193-200]
S
-
Segregation
The Effect of Silicon Content on the Graded Microstructure of Centrifugally Cast Al-Si Alloys [Volume 1, Issue 2, 2017-2018, Pages 89-97]
-
Semisolid Casting
Effect of Severe Plastic Deformation on Mechanical Properties and Microstructure of A520 Al-Alloy Produced by Semisolid and Ordinary Casting [Volume 1, Issue 1, 2017-2018, Pages 9-21]
-
Semisolid Casting
Effect of Pouring Temperature and Partial Remelting on Microstructure and Wear Properties of A390 Alloy in Slope Cooling Casting [Volume 1, Issue 1, 2017-2018, Pages 37-46]
-
Severe plastic deformation
Effect of Severe Plastic Deformation on Mechanical Properties and Microstructure of A520 Al-Alloy Produced by Semisolid and Ordinary Casting [Volume 1, Issue 1, 2017-2018, Pages 9-21]
-
Shot-peening
Effect of Shot-Peening on the Wear Behavior of Two Types of High Manganese Austenitic Steel [Volume 1, Issue 2, 2017-2018, Pages 121-132]
-
Silicon steel
Effect of Austempering Time and Temperature on the Microstructure and Hardness of Bainitic Silicon Steel [Volume 1, Issue 2, 2017-2018, Pages 79-87]
-
Simulation
Investigation on the effect of running system design on the melt flow and feeding of a hollow cylinder of A356 Al alloy by simulation [Volume 1, Issue 3, 2017-2018, Pages 133-148]
-
Solder
Production and Characterization of SAC-xAl Lead Free Nanocomposite Solder via Melt-Spinning Technique [Volume 1, Issue 3, 2017-2018, Pages 171-180]
-
Solution heat treatment
Effect of Solution Treatment on the Microstructure of γ' Precipitates in the IN738LC Superalloy Before and After Aging [Volume 1, Issue 2, 2017-2018, Pages 99-108]
-
Strength
Effect of Shot-Peening on the Wear Behavior of Two Types of High Manganese Austenitic Steel [Volume 1, Issue 2, 2017-2018, Pages 121-132]
-
Strontium
Using Thermal Analysis and Interrupted Quenching Technique to Examine Interactive Effect of Bi-Sr on Porosity Formation Characteristics in Al-7Si-0.4Mg Alloy [Volume 1, Issue 3, 2017-2018, Pages 181-191]
-
Superbainite
Effect of Austempering Time and Temperature on the Microstructure and Hardness of Bainitic Silicon Steel [Volume 1, Issue 2, 2017-2018, Pages 79-87]
-
Surface hard working
Effect of Shot-Peening on the Wear Behavior of Two Types of High Manganese Austenitic Steel [Volume 1, Issue 2, 2017-2018, Pages 121-132]
-
Surface roughness
Experimental Investigation of Effective Parameters on Gas Exhaust from the Mold in Lost Foam Casting Method [Volume 1, Issue 3, 2017-2018, Pages 161-170]
T
-
Thermal analysis
Using Thermal Analysis and Interrupted Quenching Technique to Examine Interactive Effect of Bi-Sr on Porosity Formation Characteristics in Al-7Si-0.4Mg Alloy [Volume 1, Issue 3, 2017-2018, Pages 181-191]
V
-
Vibration time
Experimental Investigation of Effective Parameters on Gas Exhaust from the Mold in Lost Foam Casting Method [Volume 1, Issue 3, 2017-2018, Pages 161-170]
W
-
Wear
Evaluation of the Microstructure and Wear Properties of A356/Al2O3 Nanocomposite Produced by Stir Casting Method [Volume 1, Issue 1, 2017-2018, Pages 59-68]
-
Wear resistance
Evaluation of Microstructure, Physical and Mechanical Properties of Functionally Graded Al-Cu Fabricated by Horizontal Centrifugal Casting [Volume 1, Issue 1, 2017-2018, Pages 47-58]
-
Wear resistance
Effect of Shot-Peening on the Wear Behavior of Two Types of High Manganese Austenitic Steel [Volume 1, Issue 2, 2017-2018, Pages 121-132]
Y
-
Yield strength of compression
Evaluation of Microstructure, Physical and Mechanical Properties of Functionally Graded Al-Cu Fabricated by Horizontal Centrifugal Casting [Volume 1, Issue 1, 2017-2018, Pages 47-58]
Your query does not match with any item